300 ml ( 35 mm ID) Super-Alloy High Pressure Reactor up to 1100C. - GSL-1100X-RC-NI300

• Reactor made of Ni-based superalloy, which allows high pressure at high temperature (up to 3 MPa at 1100 °C)
• Over-temperature alarm and interlock are installed for safe operation
• The overpressure alarm is installed. A solenoid valve is installed for automatic pressure relief
• Temperature control and pressure monitoring software are included for remote control

• Please click drawing left to see the detailed structure
• Warning #1: For your safety, never face on top flange without protective wear. 
• Warning #2: The high-pressure vessel and furnace must be placed inside an explosive-proof box or case during use under high pressure. (Please check the images below for some ideas. The customized proof is available upon request)

   

• Input voltage: 208 - 240 VAC, 50/60 Hz, single phase
• 1.5kW power

• Ni-based superalloy hydrothermal reactor with 300 mL capacity. Attention: The processing vessel is consumable, you can click the left picture to order a replacement or a spare one
• Made of Ni-based superalloy GH747 (Click to download GH747 nickel-based alloy datasheet)
• Reactor size: 70 mm OD x 35 mm ID x 326 mm H
• Air-cooled flange via aluminum heat radiator
• Gold or Ni foil can be used to wrap the crucible boat to minimize contamination to the vessel
• It is the customer's responsibility to find a suitable liner for different materials for hydrothermal crystal growth.

• 16.5 MPa (2393 PSI) ≤ 800 °C
• 10 MPa (1450 PSI) ≤ 900 °C
• 5 MPa (725 PSI) ≤ 1000 °C
• 3 MPa (435 PSI) ≤ 1100 °C

• A precision high-pressure sensor (measurement range up to 25 MPa, or 250 bar) is installed on the pressure vessel. The pressure monitor displays pressure in the bar
• A pressure monitor allows the user to set a high-pressure alarm. When the pressure reaches the alarm set point (15 MPa max), the alarm will sound and the pressure will be released via a solenoid valve on the flange. For using the reactor with a pressure > 15 MPa at low temperature, please shut off the needle valve near the solenoid valve and use the manual pressure relief valve

Temperature Control & Heater

• Working temperature: 1100 °C max (< 1 hour). Continuous working temperature: ≤ 1000 °C
• Heating/cooling rates: ≤ 10 °C/min
• Heating zone Length: 330 mm
• Constant temperature zone: 80 mm within +/- 1 °C
• Heating element: Fe-Cr-Al alloy
• Thermocouple: K-type (Omega 3 mm OD K Type with high-temperature tolerance (220°C) connector)
• One digital temperature controller with 30 programmable segments and +/- 1 ºC accuracy

• MTS-02 control software is available for real-time controlling and monitoring temperature and pressure by a computer. 

             

• SS316 needle valve with 1/4 pipe connector & pressure gauge are included
• Two consumable Copper Gasket (63 mm OD) are included (Click the left picture to order extra)

• The recommended temperature heating/cooling rate is 5~10 ºC/min
• DONOT overtighten the flange screws as this may cause permanent damage to the flange or screws. Please refer to the instruction about proper torque for installing CF flange bolts. We recommend you to use a torque wrench to tighten the screws with the flange
• DO NOT use the pressure relief solenoid valve.to vent the vessel! It could contaminate the valve and impact its service life. Always use the manual pressure relief valve for venting
• Warning: For your safety, the high-pressure vessel must be placed inside an explosive-proof box or case during use under high pressure. Never face on top flange without protection to avoid the accident.
• Please click the picture and drawing below left to see detailed structure, and click pic right to order an Explosion-Proof Box